PLX31/32 Gateways
Browse Categories
How do I get Floating Point (or Double INT or Unsigned INT) data?
All ProSoft gateways and In-Chassis modules contain a database that is based upon 16 bit words. To store 32 bit data types 2 consecutive registers or elements are required.Examples of these 32 bit data types are REAL, FLOAT and DINT's also known as double Integers.To access...
Lire la suiteNEW PLX32 Gateways - Features and Limitations
New Dual Ethernet Port Gateways Soon To Be ReleasedHere is a quick overview of the features and limitations of the soon-to-be-released PLX32 Gateways: Protocol Combinations available: * PLX32-EIP-MBTCP for Allen-Bradley EtherNet/IP to Modbus TCP/IP * PLX32-EIP-SIE for Allen-Bradl...
Lire la suiteAre the Ethernet port(s) Auto MDI-X ports?
Yes, the Ethernet port(s) will work with either cross-over cables or standard Ethernet patch cables to a switch or another device....
Lire la suiteWhich Ethernet Port is used for uploading and downloading configurations?
The first Ethernet port must be used to upload and download configuration files. It is not possible to use the second Ethernet port for this functionality....
Lire la suiteHow does the gateway know where to load or store configuration files (SD card or non-volatile RAM)?
When the PLX3x gateway boots it checks for an SD card. If an SD card is present it will load the configuration file stored on the SD card. If an SD card is not present than the gateway will load the configuration file from the non-volatile RAM in the PLX3x gateway.Note: When down...
Lire la suiteWhat do the jumpers do on the PLX3x gateways?
By default the PLX3x gateway should have the jumper in a vertical position, which places the gateway into a normal operational state.Mode 2 is used to reset the gateway to the default IP Address. To place the gateway into Mode 2 follow these steps:1) Power down the gateway2) Pla...
Lire la suiteSD Card Support on the PLX31 & PLX32 Series Gateways
The SD card slot on the PLX31 & PLX32 family of gateways is provided to simplify the process of transferring gateway configurations from one gateway to another (of the same model). It is not a requirement for the SD card to be present. During boot-up, the gateway firmware det...
Lire la suiteConfiguration Storage on the PLX31 & PLX32 Gateways
The SD card slot is provided as an optional backup mechanism for restoring configurations or transferring a configuration from one gateway to another.It is important to note that the SD card takes precedence over the gateways’ internal non-volatile storage. If the SD card is pres...
Lire la suiteDifferences between the PLX31 & PLX32 Gateways
For our PLX3x gateways that feature 2 Ethernet-based protocols (such as EtherNet/IP, Modbus/TCP, Profinet, and SIE) we offer 2 variants: the PLX31 and the PLX32. They are essentially identical except for one critical distinction.The PLX31 variant has a single Ethernet port, and s...
Lire la suiteWhy are my PLX gateway modbus serial commands not executing despite being enabled?
If your modbus serial port and its commands are both enabled, but the commands do not appear to even be executing (status shows no requests are being made, data analyzer shows nothing coming out of the port, etc.) check the value of Command Control Reg. Command Control Reg is loc...
Lire la suiteCannot Download from PC to Device in ProSoft Configuration Builder
When changing the IP address of a Modbus TCP module, the "Download from PC to Device" option can be grayed out if there are Modbus Master commands with IP addresses that still reference the old IP Address subnet. In this case the configuration is assumed invalid due to ...
Lire la suiteControlLogix PLC Communications with 4B Watchdog Super Elite via a PLX31-EIP-MBTCP
The following TechNote describes how to configure one or more Watchdog Super Elites to communicate with a Rockwell Automation ControlLogix PLC through a ProSoft PLX31-EIP-MBTCP gateway....
Lire la suite