1782-JDO Frequently Asked Questions

1.   1.       Where is the 1782-JDOx gateway User’s Manual located?

The WRC product User’s Manuals are available from our web site Support -> Technical Data: http://wrcakron.com/data.html 

2.       What is the 1782-JDOx gateway and why should I consider purchasing one for my

      DeviceNet network?

The 1782-JDOx gateway is a communication adapter device that provides you with a flexible DeviceNet-to-Optomux interface for both B1 and B2 Optomux Brainboards and associated devices. 

3.       How can I change the DeviceNet MAC ID of my 1782-JDOx?

The address of the 1782-JDOx will come preset from the factory for address 63. You may change the address using the bank of 6 DIP switches on the unit: they can be set to any address from 0 to 63 in binary (111111=address 63). The MACID or address will not change if the switches are moved while the device is powered; power must be removed and reapplied when a new switch setting and MAC ID are desired or a device reset command must be issued.

4.       What electrical connections are required for a 1782-JDOx gateway?

DeviceNet Cable Connection:

1, 5-pin pluggable header (male, Phoenix Contact MSTBA 2.5/5-G-5.08/AU or equivalent)

Serial Cable Connection: For RS-422

1, 5-pin pluggable header (male, Phoenix Contact MSTBA 2.5/5-G-5.08/AU or equivalent)

5.       How do I begin to use a 1782-JDOx gateway?

You can begin to use a 1782-JDOx gateway by following the User’s Manual Quick Start instructions.

6.       What are the LEDs on the 1782-JDOx indicating?

There are two sets of LEDs on the unit. The two green LEDs next to the serial connector are used as indicators for the serial communication receive and transmit ports. The other two bi-color LEDs are used to indicate the DeviceNet module (MS) and network (NS) status. For troubleshooting or further information on status definitions corresponding to LED actions see LED Operation in the 1782-JDOx User’s Manual.

7.       On what DIN rail can I mount the 1782-JDOx?

The 1782-JDOx can be mounted on DIN rail mount, EN 50022 (WRC50022).

8.       What are some common applications for the 1782-JDOx gateway?

A 1782-JDOx gateway provides DeviceNet communications for weigh scales, bar code readers and scanners, display panels, robots, drives, operator stations / HMI, magnetic code readers and other ASCII serial devices.

9.       Is the 1782-JDOx gateway designed to plug-n-play?

Yes, the 1782-JDOx gateway is designed to plug-n-play using our factory default settings: serial framing of 8N1, serial baudrate of 9600, max number of B1 units to read and write, number of input and output bytes, etc. The full list of default settings can be found under Default Settings in the User’s Manual.

If you wish to change any parameters from their default settings you will need to use a DeviceNet software configuration tool. Many of these tools have EDS readers, which make the editing process easier.

10.Does a 1782-JDOx gateway provide electrical isolation?

Yes, a 1782-JDOx gateway provides 1000V network electrical isolation.

11.   What are the currently available 1782-JDOx gateway models?

1782-JDO-4: Isolated RS422 Interface

12.   On what DeviceNet baud rates does the 1782-JDOx communicate?

The unit works with 125k, 250k or 500k baud rates. It is default set to autobaud on DeviceNet. A fixed baud rate of 125k, 250k or 500k may also be assigned with a software configuration tool.

13.   On what baud rates does the serial port communicate?

The serial port on the 1782-JDOx will communicate on baud rates of: 1200, 2400, 4800, 9600, 19.2k, or 38.4k baud.

14.   How do I connect a 1782-JDOx gateway to an Optomux serial network?

You connect the JDOx to a serial port Optomux Brainboard with the Phoenix connectors on the unit, which are labeled for which signal goes in each port of the connector. The RS-422 communications signal/pin assignments are as follows:

15.   How is the Master Handshake mode different from the Hardware handshake RTS/CTS?

Master Handshake mode is a data control mechanism between the DeviceNet master and the 1782-JDOx (after the JDOx receives data from serial device), communicated in IO message. The 1782-JDOx indicates new data arrival and waits for Master to issue a new record number, to be used with new data. The hardware handshaking via RTS/CTS (which is not supported in the 1782-JDOx) requires two additional signal lines on the serial side and it controls the data before it is received.

16.   When should I turn Pad Mode ON? Or what configuration parameter should I check when the scanner cannot stay connected to the 1782-JDOx due to an IO size error?

If the DeviceNet scanner or the master device needs to be pre-configured with an input (produce) size before making a connection, or if the serial device will be sending variable data size strings, you will need to turn the PAD Mode ON. This parameter should be checked if the JDOx will not stay connected due to an IO size error.

17.   What should my master device logic be doing to see if new data is present in a poll message?

The Master program logic should be looking at the Receive Record Number and comparing it with the last stored record number to monitor new data arrival in Immediate (Non-Handshake) Mode. In the Master Handshake mode, the program should be looking at the New Data bit in status and if detected, should supply the new record number and wait for the 1782-JDOx to produce data along with that record number.

18.   What does the 1782-JDOx gateway require for power?

The 1782-JDOx receives all necessary power from the DeviceNet network cable. This should be between 11 and 25 Vdc.  It consumes about 2 watts of power maximum.

19.   How do I access the serial ASCII data from a 1782-JDOx gateway?

When configuring your PLC, you have the option to memory map the ASCII data from the 1782-JDOx to a location on your PC. The ASCII data can be found at this location.

20.   When do I need to use an EDS (electronic data sheet) file for a 1782-JDOx gateway?

An EDS file is not necessary, but it makes configuring the 1782-JDOx (changing baud rate, framing, etc.) far easier than if you were to try to change the device parameters by editing the attributes of certain class objects and instances without the aid of a configuration tool. There are many software configuration tools available with EDS readers that can be used to set up the device.

21.   What is the proper cable to use for a 1782-JDOx gateway serial connection?

The proper cable selection depends upon which gateway model is used, the serial communication baud rate desired and the total cable length.  Cable selection guidelines:

1782-JDO-4: RS422 5-wire shielded

22.   Where can I purchase the proper cable for a 1782-JDOx gateway serial connection?

You can purchase the proper cable from many suppliers and fitted with the connectors required for the gateway model and serial device being used.