-
Solutions
- Amusement
- Automated Material Handling
- Automotive
- IIoT Solutions
-
PA Link Series B
A-PAL/B
The PROFIBUS PA gateway allows the user to interface PROFIBUS PA DPV0/DPV1 to either EtherNet/IP™ or Modbus® devices.
When configured as a Master, the PA Link can exchange up to 2 kilobytes of PROFIBUS PA device and status data.
The PA Link has two Ethernet ports for a Linear or Ring (Device Level Ring – DLR) Ethernet topology. The Ethernet ports can also be configured for port mirroring, allowing for better fault analysis.
The PA Link can synchronize to an NTP Server allowing for automatic time synchronization. It also supports an onboard non-volatile event log for improved fault finding. The PA Link has a built-in Power Conditioner which can supply up to 420 mA. The power conditioner is protected against a configurable overcurrent limit. The module also has a configurable built-in Fieldbus terminator.
The PA Link provides a range of statistics and tools to provide a detailed diagnostic overview of each PA Link, which speeds-up fault finding. The Slate Configuration Utility allows the user to perform a PROFIBUS PA packet capture of the running Fieldbus which can be used to analyze the bus behavior and packets received. The PA Link also provides global and device specific statistics.
- Images
- Caractéristiques Avantages
- Configuration
- Spécifications
- Matériel
- Téléchargements
- Certifications
Images
Click on image(s) to enlarge
Caractéristiques Avantages
- Direct link from PROFIBUS PA to EtherNet/IP or Modbus TCP/IP
- Exchange up to 2 kilobytes of PROFIBUS PA device and status data
- Support for up to 32 PROFIBUS PA slave devices
- Embedded 2 port Ethernet switch – DLR capable
- Built-in Isolated PA Power Conditioner – Max. 420 mA (Temperature limited)
- Configurable bus Current Protection (Trip)
- Built-in configurable Bus Terminator
- Supports PROFIBUS PA Master Redundancy (Active / Standby)
- FDT Asset Management - DTM Available
Configuration
The Slate Configuration Utility software is used for configuration and troubleshooting of the module. The stand-alone configuration utility allows users to define the setup and configuration of the PROFIBUS PA module, connections with controllers and devices.
Spécifications
EtherNet/IP Network
Specification
Rating
Connector
RJ45
Conductors
CAT5 STP/UTP
ARP Connections
Max 20
TCP Connections
Max 20
CIP Connections
Max 10
Communication Rate
10/100 Mbps
Duplex Mode
Full / Half
Auto-MDIX Support
Yes
Embedded Switch
Yes, 2x Ethernet ports
PROFIBUS PA Network
Specification
Rating
Connector
3-way terminal
PA Master Mode Support
DPV0 Data Exchange
DPV1 Class 1 Messaging
DPV1 Class 2 Messaging
DPV1 AlarmingMaximum Slave Devices
32
Isolated
Yes
Internal Power Conditioner Voltage
Max: 23.0 V DC
Min: 19.0 V DCInternal Power Conditioner Current
Max: 420 mA – Max. Ambient Temperature ≤50 °C
Max: 320 mA – Max. Ambient Temperature ≤60 °C
Max: 220 mA – Max. Ambient Temperature ≤70 °C
Note: Includes 20mA for internal MAUInternal Termination
100 Ω - Software Enabled
Matériel
Specification
Rating
Power Supply
Input: 22 to 26 VDC, (580 mA @ 24VDC)
Power Consumption
Max: 135 mA @ 24V => 3.3 W (No Bus Load)
Max: 580 mA @ 24V => 14.0 W (Full Bus Load – 420 mA)Dimensions (H x W x D)
149.0 x 34.0 x 116.0 mm
Connector
5-way terminal, 5.08 mm pitch.
Conductors
24 to 18 AWG
Enclosure Rating
IP20, NEMA/UL Open Type
Temperature
-20 to 70 °C
Humidity
0 to 95% RH, non-condensing
Earth Connection
Yes, terminal based
Emissions
IEC 61000-6-4
ESD Immunity
EN 61000-4-2
Radiated RF Immunity
IEC 61000-4-3
EFT/B Immunity
IEC 61000-4-4
Surge Immunity
IEC 61000-4-5
Conducted RF Immunity
IEC 61000-4-6
Certifications
UL/cUL; Class1, Div 2 238,99 kB Dernière Modification 25/01/2024 ODVA Certification 37,47 kB Dernière Modification 25/01/2024 ATEX Letter of Conformity 250,12 kB Dernière Modification 12/05/2022 ATEX Letter of Conformity 56,56 kB Dernière Modification 28/09/2020 CE Declaration of Conformity (CE, UKCA, RoHS, UL) 570,54 kB Dernière Modification 26/06/2026