- Solutions
- Produits
- SERVICES ET SUPPORT
-
ACTUALITÉS
- ProSoft Insights (Blog)
-
Podcast
DeviceNet Router/B
A-DNTR/B
The DeviceNet Router/B provides a powerful and easy to configure solution to exchange data between DeviceNet™ and EtherNet/IP™, Modbus TCP/IP or Modbus RTU networks.
The module can be configured as a DeviceNet Scanner or a DeviceNet Device - allowing the user to not only integrate DeviceNet devices into a Logix or Modbus system, it also allows EtherNet/IP or Modbus devices in an existing DeviceNet network.
The DeviceNet Router B is configured using the Slate Configuration Utility software tool.
The DeviceNet Router B includes a web server to display DeviceNet operation and communication statistics and advanced diagnostics functions like built-in packet capture for the various protocols. The router has two Ethernet ports to support Device-Level-Ring (DLR) architectures
- Images
- Caractéristiques Avantages
- Configuration
- Spécifications
- Matériel
- Téléchargements
- Certifications
Images
Click on image(s) to enlarge
Caractéristiques Avantages
- DeviceNet Scanner or DeviceNet Device
- Support for multiple DeviceNet network baud rates (125K, 250K, 500K)
- Support for DeviceNet pass-through or explicit messaging
- PCCC client mode to connect to Ethernet-only PanelViews to an existing DeviceNet network
- EtherNet/IP Target or Originator with support for Class 1 connections
- Supports Modbus TCP/IP (Ethernet) and Modbus RTU (Serial) Client/Server
- Direct-to-Tag Technology
- Dual Ethernet ports with support for DLR (Device Level Ring)
- Support for NTP (Network Time Protocol) for external clock synchronization
- Advanced Diagnostics, including packet capture
Configuration
The Slate Configuration Utility software is used for the configuration and troubleshooting of the module. The stand-alone configuration utility allows users to define the setup and configuration of the DeviceNet Router module, connections with controllers and devices.
Spécifications
DeviceNet Network
Specification
Description
Connector
5-way terminal, 5.08 mm pitch.
Modes
Scanner, Target (or Device)
Baud Rate
125k, 250k, 500k
DeviceNet Terminator
120 Ω (Software enabled)
DeviceNet Scanner
Specification
Description
Device Count
63
Set Target Device Node
Supported
Set Target Device Baud Rate
Supported
Device Discovery
Supported
Explicit Messaging
Supported
Supported Connections
Poll, Change of State (COS)
DeviceNet Target
Specification
Description
Supported Connections
Poll, Change of State (COS)
Input / Output Data Max
256 bytes input or output, per message
PCCC Network
Specification
Description
Max PCCC Connections
10
Max PCCC Payload
1000 bytes
EtherNet/IP Network
Specification
Description
Connector
RJ45
Conductors
CAT5 STP/UTP
ARP Connections
Max 100
TCP Connections
Max 100
CIP Connections
Max 15
Communication Rate
10/100 Mbps
Duplex Mode
Full / Half
Auto-MDIX Support
Yes
Embedded switch
Yes, 2 x Ethernet ports
Device Level Ring (DLR)
Yes
Network Time Protocol (NTP)
Yes
EtherNet/IP Originator
Specification
Description
Class 1 Cyclic Connections Supported
Yes
Class 3 / UCMM Connections Supported
Yes
Class 1 connection count
10
Class 3 / UCMM Target Device Count
10
Class 3 / UCMM Mapping Count
50
EtherNet/IP Target
Specification
Description
Class 1 Cyclic connection count
4
Logix Direct-To-Tag supported
Yes
Modbus Client
Specification
Description
Modes
Modbus TCP/IP, Modbus RTU (RS232 and 485)
Modbus RS485 Termination
125 Ω (Software enabled)
Maximum Modbus Server Devices
20
Maximum Modbus Registers mapped
100
Modbus address Range supported
0 to 65535 of each type (Holding/Input Register, Input/Coil Status)
Base Offset
Modbus (Base 0) ; PLC (Base 1)
Configurable Modbus TCP port
Yes
Data Reformatting Supported
BB AA
BB AA DD CC
CC DD AA BB
DD CC BB AA
Modbus Server
Specification
Description
Modes
Modbus TCP/IP, Modbus RTU (232 and 485)
Modbus RS485 Termination
Software set
Modbus address Range supported
0 to 65535 of each type (Holding/Input Register, Input/Coil Status)
Base Offset
Modbus (Base 0) ; PLC (Base 1)
Configurable Modbus TCP/IP port
Yes
Serial Port (RS232)
Specification
Description
RS232 Connector
9-way terminal (shared with RS485)
RS232 Conductor
24 – 18 AWG
Electrical Isolation
1000 VDC
Baud Rates
1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200
Parity/Data Bits/Stop Bits
None, Even, Odd / 8 / 1
Serial Port (RS485)
Specification
Description
RS232 Connector
9-way terminal (shared with RS485)
RS232 Conductor
24 – 18 AWG
Electrical Isolation
1500 Vrms (1 minute, maximum)
Baud Rates
1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200
Parity/Data Bits/Stop Bits
None, Even, Odd / 8 / 1
Matériel
Specification
Description
Power Supply
Input: 10 to 32 VDC, (85 mA @ 24 VDC and 180mA @ 10 VDC)
Power Consumption
2.2 W
Dimensions
149.0 x 34.0 x 116.0 mm (H x W x D)
Connector
3-way terminal
Conductors
24 to 18 AWG
Enclosure Rating
IP20, NEMA/UL Open Type
Temperature
-20 to 70 °C
Humidity
0 to 95% RH, non-condensing
Earth Connection
Yes, terminal based
Emissions
IEC61000-6-4
ESD Immunity
EN 61000-4-2
Radiated RF Immunity
IEC 61000-4-3
EFT/B Immunity
IEC 61000-4-4
Surge Immunity
IEC 61000-4-5
Conducted RF Immunity
IEC 61000-4-6
Certifications
UL/cUL; Class1, Div 2 238,99 kB Dernière Modification 25/01/2024 CE Declaration of Conformity (CE, UKCA, RoHS, UL) 924,07 kB Dernière Modification 18/07/2025 ATEX Letter Of Conformity 101,09 kB Dernière Modification 13/10/2023
